Stage 2 “Tucked” Mil-Spec Engine Harness (95-99 2G DSM)

(1 customer review)

$979.00

This stage 2 engine harness utilizes a firewall boot and a metal plate for installation as-well, but utilizes Raychem DR-25 for protection which protects the harness from any solvents.

Clear

Description

This Mil-Spec OHM Racing Plug & Play Wire Harness was designed with a “tuck” in mind.

Firewall plate and firewall boot included, this stage 2 harness does not have a master quick disconnect circular connector, if you are looking for that please check our Stage 3 harness.

OHM Racing Plug & Play Wire Harness offers Mil-Spec Teflon wire ranging from 16AWG to 22AWG and brand new pins seals and connectors. The Teflon coated wire is loomed with Raychem DR-25 heat shrink protection, firewall boot, and Raychem ES-4 adhesive lined junctions. Each brand new connector is crimped with pneumatic heads to ensure an OEM crimp, and labeled with a label. All heavy interference circuits are protected and grounded properly and no soldering is used at all on this harness (soldering can crack on vibration) only KET open barrel splicing everywhere its needed covered with adhesive heat-shrink as well. we even took the time to label every single wire for you.

The harness is 100% quality tested pin to pin, and Hi-pot tested before shipment.

100% Plug and Play

 

Harness Connector list:

Custom Plate and firewall boot (hole require on firewall for installation)

Crank angle sensor (CAS choose 95-96, 97-99 or 1G)

GM Intake air temperature (IAT for speed density)

Engine Coolant temperature (ECT)

Coolant Gauge Temperature

Idle speed (ISC) (delete if desired)

O2 Oxygen sensor (delete if desired)

Throttle position (TPS)

Mass pressure (MAP OMNI or GM)

Injector #1

Injector #2

Injector#3

Injector#4

Knock

Coil Pack

Starter

Vehicule speed sensor (VSS)

4 ECU connectors

Reverse switch (delete if desired)

Wipers (delete if desired)

Injector resistor pack (Relocated inside)

Ignition Transistor (Relocated inside)

Noise condenser (Relocated inside)

4 wire Starter Relay (80% of DSMs have stock) * relay not included*

MPI relay (96-99 DSM have stock) * relay not included*

3 Junction connectors to dash harness

Junction connector to Fuse-box harness

 

Extra options:

We work with AEM, Haltech, Link G4 and Motec so we can wire this harnesses to virtualy any standalone.

Custom ignition systems like IGN-1A are also available to be integrated.

A/C, Cruise Control 8 injectors and more… just ask us! 🙂

Estimated time 3-4 weeks for this custom order and you can E-mail us to admin@ohm-racing.com during the process and we will respond daily. You will love our customer service.

Additional information

C.A.S

95-96, 97-99, 1G

I.S.C

Stock, Delete

O2 Oxygen

Stock, Delete

M.A.P

Omni OEM, GM

1 review for Stage 2 “Tucked” Mil-Spec Engine Harness (95-99 2G DSM)

  1. Onesickdsm (verified owner)

    Bought this harness, took a little over 4 weeks to get to my door. It was well worth the money and the time. The work on these is amazing. It was put together so well, labeled. Company is amazing, always replied to my emails. Even emailed and asked me how the install went. If you want the real deal for your 2g. Look no farther. It doesn’t get any better then this. ?

Only logged in customers who have purchased this product may leave a review.