Medium Flat rate
Showing 1–50 of 91 results
-
Weld Fitting – Aluminum (M12 x 1.5)
$8.00 Add to cart
Weld Fitting – Aluminum (M12 x 1.5)
THREAD: M12 x 1.5SUITS: Coolant Temp Sensor – Small Thread$8.00 -
Weld Fitting – Aluminum ( M14 x 1.5)
$8.00 Add to cart
-
Weld Fitting – Aluminum (3/8 NPT )
$8.00 Add to cart
Weld Fitting – Aluminum (3/8 NPT )
THREAD: 3/8 NPT 18TPISUITS: Air Temp Sensor – Large Thread and Coolant Temp Sensor – Large Thread.$8.00 -
1/4″ EGT Weld-on Base Only
$8.00 Select options -
O2 Sensor weld-on bung
$12.00 Add to cart
-
1/4″ EGT Weld-on Kit
$15.00 Select options
1/4″ EGT Weld-on Kit
INCLUDES: Nut and FerruleNOTES: Compression ferrules are single use and must be replaced when replacing probes.$15.00 -
1/4″ Stainless Compression Fitting Kit
$15.00 Add to cart
1/4″ Stainless Compression Fitting Kit
THREAD: 1/8 NPTINCLUDES: Nut and FerruleNOTES: Compression ferrules are single use and must be replaced when replacing probes.$15.00 -
Sale!
Pressure Sensor Extension Kit
$30.00$28.00 Add to cart
Pressure Sensor Extension Kit
LENGTH: 450mm (18″)SUITS: 1/8th NPT Thread MAP, Oil and Fuel Pressure sensors.INCLUDES: Fragola -4 AN Hose with Male & Female 1/8th NPT Adaptors & Rubber Insulated P-Clamps.$30.00$28.00 -
Sale!
Haltech Elite CAN Cable DTM-4 to OBDII
$39.00$36.00 Add to cart
Haltech Elite CAN Cable DTM-4 to OBDII
LENGTH: 1800mm (72″)NOTES: Vehicle side OBDII Connector$39.00$36.00 -
Sale!
Haltech Elite CAN Cable DTM-4 to DTM-4
$39.00$37.00 Select Options
-
Sale!
Haltech CAN Adaptor Cable DTM-4 Female Receptacle/Socket to 8 pin Black Tyco
$39.00$37.00 Select Options
Haltech CAN Adaptor Cable DTM-4 Female Receptacle/Socket to 8 pin Black Tyco
LENGTH: 3″ to 120”SUITS: Used to adapt a Platinum series ECU to Elite DTM-4 CAN system.$39.00$37.00 -
Sale!
Coolant Temp Sensor – Small Thread
$39.00$38.00 Add to cart
Coolant Temp Sensor – Small Thread
THREAD: M12 x 1.5INCLUDES: Matching Delphi plug and pins.NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Sale!
Coolant Temp Sensor – Large Thread
$39.00$38.00 Add to cart
Coolant Temp Sensor – Large Thread
THREAD: 3/8 NPT 18TPIINCLUDES: Matching Delphi plug and pins.NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Sale!
Coolant Temp Sensor
$39.00$38.00 Add to cart
Coolant Temp Sensor
THREAD: 1/8 NPT 27TPIINCLUDES: Matching male Deutsch DTM-2 Connector (HT-031000)NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Sale!
Air Temp Sensor – Small Thread THREAD: M14 x 1.5
$39.00$38.00 Add to cart
Air Temp Sensor – Small Thread THREAD: M14 x 1.5
THREAD: M14 x 1.5INCLUDES: Matching Delphi plug and pins.NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Sale!
Air Temp Sensor – Large Thread
$39.00$38.00 Add to cart
Air Temp Sensor – Large Thread
THREAD: 3/8 NPT 18TPIINCLUDES: Matching Delphi plug and pins.NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Sale!
Air Temp Sensor
$39.00$38.00 Add to cart
Air Temp Sensor
THREAD: 1/4 NPTSUITS: Nissan Z32 300ZX intake.INCLUDES: Matching Delphi plug and pins.NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Sale!
Air Temp Sensor DTM
$39.00$38.00 Add to cart
Air Temp Sensor DTM
THREAD: 1/8 NPTINCLUDES: Matching male Deutsch DTM-2 Connector (HT-031000)NOTES: 127 deg C (260 F) Max reading.$39.00$38.00 -
Wideband Extension Harness To suit LSU4.9
$38.00 Add to cart
-
Sale!
AEM Water/Oil Temperature Sensors
$38.58 – $51.21 Select options
AEM Water/Oil Temperature Sensors
AEM offers 1/8″ NPT DTM-Style Connector(PN 30-2013), 1/8″ NPT (PN 30-2012) and 3/8″ NPT (PN 30-2011) water/oil temperature sensor kit.
$38.58 – $51.21 -
Flex Fuel Fittings 3/8 “GM Spring Lock” -6AN Male
$44.00 Add to cart
Flex Fuel Fittings 3/8 “GM Spring Lock” -6AN Male
SUITS: GM Flex Fuel Sensors.INCLUDES: Two fittings.$44.00 -
iC-7 Standard Dash Mount
$52.00 Add to cart
iC-7 Standard Dash Mount
SUITS: Haltech iC-7 Display DashINCLUDES: 1 x 2.5mm Black Annodized Aluminium BracketNOTES: Suits Haltech iC-7 Display Dash$52.00 -
iC-7 Mounting Bracket with Integrated Visor
$64.00 Add to cart
iC-7 Mounting Bracket with Integrated Visor
SUITS: Haltech iC-7 Display DashINCLUDES: 1 x 2.5mm Black Annodized Aluminium Bracket with integrated Visor and Laser Etched Haltech LogoNOTES: Suits Haltech iC-7 Display Dash$64.00 -
OHM Racing high quality silicone hoses (clamps included) (95-99 DSM)
$64.99 Select options
OHM Racing high quality silicone hoses (clamps included) (95-99 DSM)
Our own OHM Racing High quality silicone hoses with clamps.
$64.99 -
OHM Racing high quality silicone hoses (clamps included) (90-94 DSM)
$64.99 Select options
OHM Racing high quality silicone hoses (clamps included) (90-94 DSM)
Our own OHM Racing high quality silicone hoses with clamps.
$64.99 -
12 Position Rotary Trim Module (Boost/Fuel/Ign etc)
$67.00 Add to cart
12 Position Rotary Trim Module (Boost/Fuel/Ign etc)
INCLUDES: 2 position decals and matching set of Deutsch DTM 3 connectors (HT-031014)$67.00 -
Sale!
Oil Temperature sensor High Range
$78.00$74.00 Add to cart
Oil Temperature sensor High Range
THREAD: 1/8 NPT 27TPIINCLUDES: Matching Bosch EV1 plug & pins.NOTES: 150 deg C (302 F) Max reading.$78.00$74.00 -
Haltech iC-7 Tube Mount For tube OD 1.25in Size: 60mm x 44mm
$74.00 Add to cart
Haltech iC-7 Tube Mount For tube OD 1.25in Size: 60mm x 44mm
SIZE: 60mm x 44mmSUITS: Haltech iC-7 Mounting Brackets (HT-060070 and HT-060071)INCLUDES: 1 x Annodized Dash Tube Mount 2 x Zinc M8 x 10 Bracket Mounting Screws 4 x Zinc M6 x 25 Assembly ScrewsNOTES: Designed to be used with optional dash mounting brackets HT-060070 and HT-060071 (sold seperately)$74.00 -
Sale!
High Output IGN-1A Inductive Coil with built-in Ignitor (Smart Coil)
$75.00$74.00 Add to cart
High Output IGN-1A Inductive Coil with built-in Ignitor (Smart Coil)
INCLUDES: Matching plug and pins.
$75.00$74.00 -
1/4″ Open Tip Thermocouple (24” to 96”)
$81.00 Select options
1/4″ Open Tip Thermocouple (24” to 96”)
LENGTH: (24” to 96”)SUITS: NA or Forced induction applications. Used with a Requires a TCA 2 or 4 thermocouple amplifier.INCLUDES: Mini K Type connector.NOTES: Does not include any fitting hardware. Please order seperately if required.$81.00 -
Sale!
Elite CAN HUB 4 Port DTM-4
$110.00$104.00 Add to cart
Elite CAN HUB 4 Port DTM-4
SUITS: For use with up to three CAN devices.INCLUDES: Elite 4 Port CAN hub and Elite CAN cable DTM-4 to DTM-4 – 300mm (12″)NOTES: Direct Plug ‘n’ Play compatible with an Elite ECU CAN port or Elite ECU Harness CAN connector. Combine two or more Elite CAN Hubs as required to connect mutiple CAN devices to your ECU.$110.00$104.00 -
Sale!
Boost Control Solenoid 3 Port 33Hz
$118.00$111.00 Add to cart
Boost Control Solenoid 3 Port 33Hz
THREAD: 1/8 NPTINCLUDES: Hose fittings, rubber isolated mount and matching Set of Deutsch DTM 2 Connectors (HT-031012)$118.00$111.00 -
Wideband Sensor – Bosch LSU 4.9
$112.00 Add to cart
Wideband Sensor – Bosch LSU 4.9
SUITS: Elite Pro Plugin ECU and WB1/WB2INCLUDES: Bosch LSU 4.9 sensor with Factory calibration resistor connector (not a Deutsch DT-6 connector)$112.00 -
EVO 4-9 OHM Racing IGN-1A Coil Plate
$119.99 Select Options
-
DSM/EVO 1-3/GVR4 OHM Racing IGN-1A Coil Plate
$124.99 Select Options
DSM/EVO 1-3/GVR4 OHM Racing IGN-1A Coil Plate
If you are looking for making your own kit, this nice plate is a must have, run all the wiring through the bottom to keep things clean!
$124.99 -
4 Bar Motorsport MAP Sensor
$142.00 Add to cart
-
Onboard Wideband Sensor Pack for Elite PRO Plug-in ECUs
$149.00 Add to cart
Onboard Wideband Sensor Pack for Elite PRO Plug-in ECUs
SUITS: Elite PRO Plug-in ECUs for Australian-made Ford “Barra” Falcons only.INCLUDES: O2 Sensor, 1.2m extension cable and weld-on bung.$149.00 -
Dual Switch Panel Kit
$149.00 Add to cart
Dual Switch Panel Kit
INCLUDES: Dual panel, yellow adjustment knob and 2 x 12 position rotary trim modules.$149.00 -
EVO X OHM Racing IGN-1A Coil Plate
$149.99 Select Options
-
Sale!
AEM MAP/PSIa Sensors (Stainless Steel) 15-30-50-75 PSI
$152.00 – $155.00 Select options
AEM MAP/PSIa Sensors (Stainless Steel) 15-30-50-75 PSI
AEM offers high quality stainless steel PSIa sensors in 15 (1BAR), 30 (2BAR), 50 (3.5BAR), 75 (5BAR) and 100 (7BAR). PSIa is referenced to absolute zero. Absolute zero is the pressure measurement when all the pressure exerted by the atmosphere has been removed. The most common use for absolute pressure sensors is reading manifold pressure.
$152.00 – $155.00 -
OHM Custom IGN-1A Smart Coil Ignition Wires (DSM/EVO1-3/GVR4)
$159.99 Add to cart
OHM Custom IGN-1A Smart Coil Ignition Wires (DSM/EVO1-3/GVR4)
Custom OHM Ignition wires for your IGN-1a ignition system.
$159.99 -
Sale!
OHM Custom IGN-1A Smart Coil Ignition Wires (EVO 4-9)
$174.99 – $189.99 Select options
OHM Custom IGN-1A Smart Coil Ignition Wires (EVO 4-9)
Custom Ignition wires for your IGN-1a ignition system with your choice of 8.5 or 10mm.
$174.99 – $189.99 -
150 PSI “TI” Fuel/Oil/Wastegate Pressure Sensor
$186.00 Add to cart
150 PSI “TI” Fuel/Oil/Wastegate Pressure Sensor
THREAD: 1/8 NPTINCLUDES: Matching Delphi plug and 3 pins, -4 AN adaptor.NOTES: “TI” Pressure sensors must not be mounted directly into the fuel rail or engine block, they must be remote mounted and connected via a flexible hose – If required use Pressure Sensor Extension Hose HT-039103$186.00 -
250 PSI “TI” Fuel/Oil/Wastegate Pressure Sensor
$186.00 Add to cart
250 PSI “TI” Fuel/Oil/Wastegate Pressure Sensor
THREAD: 1/8 NPTINCLUDES: Matching plug and pins, -4 AN adaptor.NOTES: “TI” Pressure sensors must not be mounted directly into the fuel rail or engine block, they must be remote mounted and connected via a flexible hose – If required use Pressure Sensor Extension Hose HT-039103$186.00 -
150 PSI Motorsport Fuel/Oil/Wastegate Pressure Sensor (Stainless Steel Diaphragm)
$186.00 Add to cart
150 PSI Motorsport Fuel/Oil/Wastegate Pressure Sensor (Stainless Steel Diaphragm)
THREAD: 1/8 NPT
INCLUDES: Matching Delphi plug and 3 pins.
NOTES: Motorsport Pressure sensors must not be mounted directly into the fuel rail or engine block, they must be remote mounted and connected via a flexible hose – If required use Pressure Sensor Extension Hose HT-039103$186.00 -
250 PSI Motorsport Fuel/Oil/Wastegate Pressure Sensor (Stainless Steel Diaphragm)
$186.00 Add to cart
250 PSI Motorsport Fuel/Oil/Wastegate Pressure Sensor (Stainless Steel Diaphragm)
THREAD: 1/8 NPTINCLUDES: Matching Delphi plug and 3 pins.NOTES: Motorsport Pressure sensors must not be mounted directly into the fuel rail or engine block, they must be remote mounted and connected via a flexible hose – If required use Pressure Sensor Extension Hose HT-039103$186.00 -
Flex Fuel Composition Sensor
$186.00 Add to cart
Flex Fuel Composition Sensor
SUITS: 3/8 “GM Spring Lock” fittings.INCLUDES: Matching plug and 3 pins.$186.00 -
5 Bar “TI” MAP Sensor
$224.00 Add to cart
5 Bar “TI” MAP Sensor
THREAD: 1/8 NPTINCLUDES: Matching Delphi plug and 3 pins, -4 AN & 5mm hosetail adaptors.NOTES: “TI” MAP sensors must not be mounted directly to the inlet manifold, they must be remote mounted and connected via a flexible hose – If required use Pressure Sensor Extension Hose HT-039103$224.00 -
5 Bar Motorsport MAP Sensor (Stainless Steel Diaphragm)
$224.00 Add to cart
5 Bar Motorsport MAP Sensor (Stainless Steel Diaphragm)
THREAD: 1/8 NPTINCLUDES: Matching Delphi plug and 3 pins.NOTES: Motorsport MAP sensors must not be mounted directly to the inlet manifold, they must be remote mounted and connected via a flexible hose – If required use Pressure Sensor Extension Hose HT-039103$224.00 -
Triple Switch Panel Kit
$224.00 Add to cart
Triple Switch Panel Kit
INCLUDES: Triple panel, yellow and red adjustment knobs and 3 x 12 position rotary trim modules.$224.00
