haltech
Showing 1–24 of 130 resultsSorted by price: low to high
-
Weld Fitting – Aluminum Thread: M12 x 1.5
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
-
Weld Fitting – Aluminum Thread: 3/8 NPT 18TPI
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
Weld Fitting – Aluminum Thread: 3/8 NPT 18TPI
Suits: Air Temp Sensor – Large Thread and Coolant Temp Sensor – Large Thread.$16.00 -
Pins only – Suit Fuses only in the 6 Circuit Haltech Fuse Box -Pack of 10
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart -
Power Relay 30A 5 Pin
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
-
Pins only – Suit Relays only in the 6 Circuit Haltech Fuse Box -Pack of 10
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart -
Weld on Fitting 1/8 NPT – 27 TPI – 6061 Aluminium Size: 20.4mm x 13mm
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
Weld on Fitting 1/8 NPT – 27 TPI – 6061 Aluminium Size: 20.4mm x 13mm
Includes: 1 x 1/8 NPT Weld on fitting
$16.00 -
Adaptor – Brass 1/8″ NPTF to 3/8″ NPTF Length: 20mm
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
Adaptor – Brass 1/8″ NPTF to 3/8″ NPTF Length: 20mm
Suits: 1/8″ NPT Sensors
Includes: Adaptor Only
Notes: Tightening Torque: 1.5 – 3 TPFT (Turns past finger tight)
$16.00 -
O2 Sensor weld-on bung – 6061 Aluminium Thread: M18 x1.5
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
O2 Sensor weld-on bung – 6061 Aluminium Thread: M18 x1.5
Suits: M18 Thread Oxygen Sensors
Includes: 1 x 6061 Aluminium Weld On Bung
$16.00 -
1/4″ Nut and Brass Ferrule Only
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
1/4″ Nut and Brass Ferrule Only
Notes: Compression ferrules are single use and must be replaced when replacing probes.
$16.00 -
1/4″ Mild Steel Weld-on Base Only
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
-
1/4″ Stainless Steel Weld-on Base Only
$16.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
-
1/4″ Stainless Compression Fitting Kit Thread: 1/8 NPT
$21.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
1/4″ Stainless Compression Fitting Kit Thread: 1/8 NPT
Includes: Nut and Ferrule
Notes: Compression ferrules are single use and must be replaced when replacing probes.
$21.00 -
CAN Keypad Label Set
$21.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
CAN Keypad Label Set
Suits: Haltech CAN Keypads
Includes: 5 Label Sheet (140 individual labels)
Notes: A selection of pre designed, semi transparent labels to suit the backlit Haltech CAN Keypads.
$21.00 -
1/4″ Mild Steel Weld-on Kit
$21.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
1/4″ Mild Steel Weld-on Kit
Includes: Nut and Ferrule
Notes: Compression ferrules are single use and must be replaced when replacing probes.
$21.00 -
1/4″ Stainless Steel Weld-on Kit
$21.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
1/4″ Stainless Steel Weld-on Kit
Includes: Nut and Ferrule
Notes: Compression ferrules are single use and must be replaced when replacing probes.
$21.00 -
CAN Adaptor Loom DTM-4 to Flying Leads
$26.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
CAN Adaptor Loom DTM-4 to Flying Leads
Suits: Haltech IC-7 Dash, WB1, WB2, and aftermarket ECUs using the AMP Superseal 1.0 Series Connector
Includes: 1 x HT-130046 CAN Adaptor Loom (DTM-4 to Flying leads)
Notes: Suits aftermarket ECUs using the AMP Superseal 1.0 Series Connector Terminated with 2 x Pins to suit connector.
$26.00 -
M10 x 1.0 to 1/8 BSPT Adaptor Thread: M10 x 1.0 Female to 1/8BSPT Male
$26.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
M10 x 1.0 to 1/8 BSPT Adaptor Thread: M10 x 1.0 Female to 1/8BSPT Male
Suits: Bosch Fluid Pressure and Temperature Sensor – HT-010920
Includes: 1x M10x 1.0 to 1/8 BSPT Adaptor
Notes: Use with Bosch Fluid Pressure and Temperature Sensor – HT-010920
$26.00 -
Rare Earth Magnets Size: 5mm Diameter x 2mm Height
$26.00Pay with Affirm on orders over $35. Check your purchasing power
Add to cart
-
Mitsu Style MAP to AEM/Haltech/Delphi/GM pressure sensor Adapter
$34.99-
Select options This product has multiple variants. The options may be chosen on the product page
Mitsu Style MAP to AEM/Haltech/Delphi/GM pressure sensor Adapter
Mitsu Style MAP Adapter: Fits AEM, Haltech, MoTeC, and similar Pressure sensors.
$34.99Select options This product has multiple variants. The options may be chosen on the product page -
Haltech CAN Cable 8 pin Black Tyco to 8 pin Black Tyco Length: 75mm (3″)
$35.00-
Read more
Haltech CAN Cable 8 pin Black Tyco to 8 pin Black Tyco Length: 75mm (3″)
Haltech CAN Cable 8 pin Blk Tyco 8 pin Blk Tyco 75mm (3″)
$35.00 -
Haltech CAN Cable 8 pin White Tyco to 8 pin White Tyco Length: 75mm (3″)
$35.00-
Read more
Haltech CAN Cable 8 pin White Tyco to 8 pin White Tyco Length: 75mm (3″)
Haltech CAN Cable 8 pin Wh Tyco 8 pin Wh Tyco 75mm (3″)
$35.00 -
Haltech CAN Cable 8 pin Black Tyco to 8 pin Black Tyco Length: 150mm (6″)
$35.00-
Read more
Haltech CAN Cable 8 pin Black Tyco to 8 pin Black Tyco Length: 150mm (6″)
Haltech CAN Cable 8 pin Blk Tyco 8 pin Blk Tyco 150mm (6″)
$35.00 -
Haltech CAN Cable 8 pin White Tyco to 8 pin White Tyco Length: 150mm (6″)
$35.00-
Read more
Haltech CAN Cable 8 pin White Tyco to 8 pin White Tyco Length: 150mm (6″)
Haltech CAN Cable 8 pin Wh Tyco 8 pin Wh Tyco 150mm (6″)
$35.00 -
Haltech CAN Cable 8 pin Black Tyco to 8 pin Black Tyco Length: 300mm (12″)
$35.00-
Read more
Haltech CAN Cable 8 pin Black Tyco to 8 pin Black Tyco Length: 300mm (12″)
Haltech CAN Cable 8 pin Blk Tyco 8 pin Blk Tyco 300mm (12″)
$35.00
